是在sun网站上看到的，原文是e文，连接如下：
http://www.adminschoice.com/docs/iostat_vmstat_netstat.htm
大概翻译了一下，总觉得好像以前哪位大大贴过类似的
不管了，觉得有点用，大家一起看看
翻译得不好，见笑了……如果有错，请指正哦，先谢了
[b:38a037c632]Input Output statistics ( iostat )[/b:38a037c632]
iostat反映了终端、磁盘I/O情况和CPU活动。输出结果的第一行是从系统启动到现在为止的这段时间的结果，接下去的每一行是interval时
间段内的结果。Kernel里有一组计数器用来跟踪这些值。
iostat的默认参数是tdc(terminal, disk, and CPU)。如果任何其他的选项被指定，这个默认参数将被完全替代，例如，iostat -d将只反
映磁盘的统计结果。
语法:
基本语法： iostat <options> interval count
option - 让你指定所需信息的设备，像磁盘、cpu或者终端(-d , -c , -t or -tdc ) 。x 选项给出了完整的统计结果（gives the extended
statistic）。
interval - 在两个samples之间的时间（秒）。
count - 就是需要统计几次
例子：
$ iostat -xtc 5 2
extended disk statistics tty cpu
disk r/s w/s Kr/s Kw/s wait actv svc_t %w %b tin tout us sy wt id
sd0 2.6 3.0 20.7 22.7 0.1 0.2 59.2 6 19 0 84 3 85 11 0
sd1 4.2 1.0 33.5 8.0 0.0 0.2 47.2 2 23
sd2 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0 0
sd3 10.2 1.6 51.4 12.8 0.1 0.3 31.2 3 31
The fields have the following meanings:
disk name of the disk
r/s reads per second
w/s writes per second
Kr/s kilobytes read per second
Kw/s kilobytes written per second
wait average number of transactions waiting for service (Q length)
actv average number of transactions actively
being serviced (removed from the
queue but not yet
completed)
%w percent of time there are transactions waiting
for service (queue non-empty)
%b percent of time the disk is busy (transactions
in progress)
Results and Solutions:
从iostat输出结果中需要注意的值：
Reads/writes per second (r/s , w/s)
Percentage busy (%b)
Service time (svc_t)
如果磁盘显示长时间的高reads/writes，并且磁盘的percentage busy (%b)也远大于5%，同时average service time (svc_t)也远大于30
milliseconds，这以下的措施需要被执行：
1.)调整应用，令其使用磁盘i/o更加有效率，可以通过修改磁盘队列、使用应用服务器的cache
2.)将文件系统分布到2个或多个磁盘上，并使用volume manager/disksuite的条带化特点
3.) 增加系统参数值，如inode cache , ufs_ninode。Increase the system parameter values for inode cache , ufs_ninode , which
is Number of inodes to be held in memory. Inodes are cached globally (for UFS), not on a per-file system basis
4.) 将文件系统移到更快的磁盘/控制器，或者用更好的设备来代替
:em06: 还有两段等会翻好了再贴……
| zat 回复于：2004-06-14 14:36:25 |
| Virtual Memory Statistics ( vmstat )
vmstat - vmstat反映了进程的虚拟内存、虚拟内存、磁盘、trap(是不是翻译成中断？？)和cpu的活动情况 在多cpu系统中，vmstat在输出结果中平均了cpu数量。For per-process statistics .如果没有选项，vmstat显示一行虚拟内存活动的概要 结果，是从系统启动时开始的。 语法: vmstat <options> interval count option - 让你指定所需的信息类型，例如 paging -p , cache -c ,.interrupt -i etc. 如果没有指定选项，将会显示进程、内存、页、磁盘、中断和cpu信息 interval - 同iostat count - 同iostat 例子 The following command displays a summary of what the system is doing every five seconds. example% vmstat 5 procs memory page disk faults cpu r b w swap free re mf pi p fr de sr s0 s1 s2 s3 in sy cs us sy id 0 0 0 11456 4120 1 41 19 1 3 0 2 0 4 0 0 48 112 130 4 14 82 0 0 1 10132 4280 0 4 44 0 0 0 0 0 23 0 0 211 230 144 3 35 62 0 0 1 10132 4616 0 0 20 0 0 0 0 0 19 0 0 150 172 146 3 33 64 0 0 1 10132 5292 0 0 9 0 0 0 0 0 21 0 0 165 105 130 1 21 78 The fields of vmstat's display are procs r in run queue b blocked for resources I/O, paging etc. w swapped memory (in Kbytes) swap - amount of swap space currently available free - size of the free list page ( in units per second). re page reclaims - see -S option for how this field is modified. mf minor faults - see -S option for how this field is modified. pi kilobytes paged in po kilobytes paged out fr kilobytes freed de anticipated short-term memory shortfall (Kbytes) sr pages scanned by clock algorithm disk ( operations per second ) There are slots for up to four disks, labeled with a single letter and number. The letter indicates the type of disk (s = SCSI, i = IPI, etc) . The number is the logical unit number. faults in (non clock) device interrupts sy system calls cs CPU context switches cpu - breakdown of percentage usage of CPU time. On multiprocessors this is an a verage across all processors. us user time sy system time id idle time 结果和解决方案: A. CPU issues: 下面几列需要被察看，以确定cpu是否有问题 Processes in the run queue (procs r) User time (cpu us) System time (cpu sy) Idle time (cpu id) procs cpu r b w us sy id 0 0 0 4 14 82 0 0 1 3 35 62 0 0 1 3 33 64 0 0 1 1 21 78 问题情况: 1.) 如果processes in run queue (procs r)的数量远大于系统中cpu的数量，将会使系统便慢。 2.) 如果这个数量是cpu的4倍的话，说明系统正面临cpu能力短缺,这将使系统运行速度大幅度降低 3.) 如果cpu的idle时间经常为0的话，或者系统占用时间(cpu sy)是用户占用时间(cpu us)两辈的话，系统面临缺少cpu资源 解决方案 : 解决这些情况，涉及到调整应用程序，使其能更有效的使用cpu，同时增加cpu的能力或数量。 B. Memory Issues: 内存的瓶颈取决于scan rate (sr) 。scan rate是每秒时钟对页的扫描 （he scan rate is the pages scanned by the clock algorithm per second.）如果 scan rate (sr)一直大于200 pages每秒，这时就是内存短缺的现实。 解决方案 : 1. 调整应用和服务器，使其能更好的使用memory和cache 2. 增加系统内存 3. Implement priority paging in s in pre solaris 8 versions by adding line "set priority paging=1" in /etc/system. Remove this line if upgrading from Solaris 7 to 8 & retaining old /etc/system file. |
| zat 回复于：2004-06-14 16:13:19 |
| Network Statistics (netstat)
netstat通过选项来显示不通的网络相关的数据结构（netstat displays the contents of various network-related data structures in depending on the options selected.） 语法 : netstat <option/s> 多个选项可以同时使用 Options -a - displays the state of all sockets. -r - shows the system routing tables -i - gives statistics on a per-interface basis. -m - displays information from the network memory buffers. On Solaris, this shows statistics forSTREAMS -p [proto] - retrieves statistics for the specified protocol -s - shows per-protocol statistics. (some implementations allow -ss to remove fileds with a value of 0 (zero) from the display.) -D - display the status of DHCP configured interfaces. -n do not lookup hostnames, display only IP addresses. -d (with -i) displays dropped packets per interface. -I [interface] retrieve information about only the specified interface. -v be verbose interval - number for continuous display of statictics. Example : $netstat -rn Routing Table: IPv4 Destination Gateway Flags Ref Use Interface -------------------- -------------------- ----- ----- ------ --------- 192.168.1.0 192.168.1.11 U 1 1444 le0 224.0.0.0 192.168.1.11 U 1 0 le0 default 192.168.1.1 UG 1 68276 127.0.0.1 127.0.0.1 UH 1 10497 lo0 这个显示了一台solaris机器的ip为192.168.1.11，他的默认网关192.168.1.1 结果和解决方案: A.)网络连通 上面的命令经常用来检查网络的连通性。特别是当机器无法访问外部网络时： 1. 默认路由ip是否正确 2. 能否ping通网关 3. 如果网关地址不对，可以使用route add命令，参考 man route route command examples: $route add default <hostname> $route add 192.0.2.32 <gateway_name> If the router address is correct but still you can't ping it there may be some network cable /hub/switch problem and you have to try and eliminate the faulty component . B.) 网络反映 $ netstat -i Name Mtu Net/Dest Address Ipkts Ierrs Opkts Oerrs Collis Queue lo0 8232 loopback localhost 77814 0 77814 0 0 0 hme0 1500 server1 server1 10658566 3 4832511 0 279257 0 这个选项用于诊断网络问题，网络连通但连接速度慢 Values to look at: Collisions (Collis) Output packets (Opkts) Input errors (Ierrs) Input packets (Ipkts) The above values will give information to workout i. Network collision rate(网络冲突率)如下 : Network collision rate = Output collision counts / Output packets 网络冲突率大于10%就显示，网络负载过大、网络配置不正确、硬件问题 ii. Input packet error rate（进入包错误率）如下 : Input Packet Error Rate = Ierrs / Ipkts. 如果input error rate高（ver 0.25 percent），这个主机就正在丢包。hub/switch 连线就需要被检查是否存在潜在的问题。 C. Network socket & TCP Cconnection state netstat给出了关于网络socket和tcp state的重要信息。只是非常有用的，在寻找开放、关闭和等待网络tcp连接。 netstat返回如下的网络状态 : CLOSED ---- Closed. The socket is not being used. LISTEN ---- Listening for incoming connections. SYN_SENT ---- Actively trying to establish connection. SYN_RECEIVED ---- Initial synchronization of the connection under way. ESTABLISHED ---- Connection has been established. CLOSE_WAIT ---- Remote shut down; waiting for the socket to close. FIN_WAIT_1 ---- Socket closed; shutting down connection. CLOSING ---- Closed, then remote shutdown; awaiting acknowledgement. LAST_ACK ---- Remote shut down, then closed ;awaiting acknowledgement. FIN_WAIT_2 ---- Socket closed; waiting for shutdown from remote. TIME_WAIT ---- Wait after close for remote shutdown retransmission. Example: #netstat -a Local Address Remote Address Swind Send-Q Rwind Recv-Q State *.* *.* 0 0 24576 0 IDLE *.22 *.* 0 0 24576 0 LISTEN *.22 *.* 0 0 24576 0 LISTEN *.* *.* 0 0 24576 0 IDLE *.32771 *.* 0 0 24576 0 LISTEN *.4045 *.* 0 0 24576 0 LISTEN *.25 *.* 0 0 24576 0 LISTEN *.5987 *.* 0 0 24576 0 LISTEN *.898 *.* 0 0 24576 0 LISTEN *.32772 *.* 0 0 24576 0 LISTEN *.32775 *.* 0 0 24576 0 LISTEN *.32776 *.* 0 0 24576 0 LISTEN *.* *.* 0 0 24576 0 IDLE 192.168.1.184.22 192.168.1.186.50457 41992 0 24616 0 ESTABLISHED 192.168.1.184.22 192.168.1.186.56806 38912 0 24616 0 ESTABLISHED 192.168.1.184.22 192.168.1.183.58672 18048 0 24616 0 ESTABLISHED if you see a lots of connections in FIN_WAIT state tcp/ip parameters have to be tuned because the connections are not being closed and they gets accumulating . After some time system may run out of resource . TCP parameter can be tuned to define a time out so that connections can be released and used by new connection. A detailed document about tuning tcp/ip can be found at http://www.sean.de/Solaris/soltune.html |
| amiescort 回复于：2004-06-15 13:23:26 |
| 丁页一下，楼主辛苦了 |
| smartlam 回复于：2004-06-27 15:29:27 |
| 好贴，顶一下。 |
| liguang668 回复于：2005-02-22 12:25:36 |
| 非常棒！我顶！ |
| jian-yuyu 回复于：2005-02-22 17:19:00 |
| 谢谢楼主! |
延伸阅读
文章来源于领测软件测试网 https://www.ltesting.net/
