多播配置

领测软件测试网

　　 
　　源码:--------------------------------------------------------------------------------
　　Multicast is a UDP-based protocol which literally delivers packets from one
　　host to many. If abused, it can be made to deliver from many hosts to

　　many hosts to many hosts to many hosts... This is why it's important to
　　setup multicasting routing on the routers in a sane manner.
　　
　　1. First, enable the global multicast routing parameter by:
　　 !
　　 ip multicast-routing
　　 !
　　 This can be disabled, if you so choose, by doing:
　　 !
　　 no ip multicast-routing
　　 !
　　
　　2. Next, select your style of multicasting. I chose PIM (Protocol-
　　 Independent Multicast) for the following reasons:
　　 - PIM works with all existing multicast routing protocols.
　　 - PIM has two modes (dense & sparse) which gives me some freedom at
　　 configuration time.
　　 You could also choose from IGMP (Internet Group Management Protocol,
　　 which is good for large WANs) or DVMRP (Distance Vector Multicast
　　 Routing Protocol, which is slightly unsupported). However, be aware
　　 that Cisco only tacitly supports DVMRP. To use DVMRP with a Cisco
　　 router, you need to point your Cisco to a router that DOES support
　　 DVMRP directly.
　　
　　 Of the two PIM choices, I went with dense mode. Here are the differences:
　　 - Dense mode: When the router receives a multicast packet, the router
　　 sends the packet out of all interfaces except for the interface from
　　 whence the packet originated. If the router discovers that a certain
　　 interface has no multicast recipients, it sends a "prune" message back
　　 to the sender stating that there is no need to send messages to that
　　 interface/subnet/link/host.
　　 - Sparse mode: In sparse mode, it is assumed that no host wants multi-
　　 cast packets unless the host specifically asks for it. So, instead
　　 of the shotgun approach of dense mode, one router becomes the central
　　 hub. This central hub logs all hosts that wish to receive multicast.
　　 Further multicast packets are sent only to those hosts.
　　 Seeing as how we only have two routers, I did not want one router to be
　　 burdened with the list of multicast hosts (especially since practically
　　 ALL of our hosts "want" multicast). Additionally, I did not want to
　　 spend time fudging entries in the multicast recipient list.
　　
　　 So, to configure for PIM dense mode multicast routing:
　　 !
　　 interface ethernet 0
　　 ip pim dense-mode
　　 !
　　 interface ethernet 1
　　 ip pim dense-mode
　　 !
　　 Obviously, all involved routers should be speaking the same lingo. Thus,
　　 routerA is configured the same as routerB.
　　
　　3. Next, you need to set the multicast threshold. This is the BIG TRICK[tm]
　　 to multicast routing. In a nutshell, every multicast packet has a TTL.
　　 That's basic to all IP. By setting the multicast threshold on a given
　　 router interface, you create a hurdle. If the packet's TTL is higher
　　 than the multicast threshold, the packet may pass. If the packet's TTL
　　 is LOWER than the multicast threshold, the packet is stopped (actually,
　　 it is bounced with an ICMP message, but that's for another "howto" ;-).
　　
　　 This is how one prevents multicast packets from careening out into the
　　 great 'Net. The range for multicast threshold is 0 to 255, with 0
　　 meaning all packets may pass (well, *almost* all) and 255 meaning
　　 virtually no packets may pass. On the routerB router, I set up the
　　 multicast threshold at a comfortable 1 (because this is an internal
　　 router). The multicast threshold on the interface leading to the
　　 Internet on routerA should be set at 255 (if, in fact, multicast is
　　 enabled on the interface at all).
　　 !
　　 interface ethernet 0
　　 ip multicast-threshold 1
　　 !
　　 interface ethernet 1
　　 ip multicast-threshold 1
　　 !
　　 And you're set!
　　
　　4. It's probably a VERY good idea at this point to save your config. I
　　 choose to save off to tftp (in case my NVRAM gets scrammed), but you
　　 can choose your own danger here. At the least, you should copy your
　　 running-config to your saved config.
　　 router#copy running-config startup-config

文章来源于领测软件测试网 https://www.ltesting.net/